A szett tartalma: 1 db Sony LMD-A170 + 1 db Sony BKM-PL17
Picture Performance:
| Panel | a-Si TFT Active Matrix LCD |
| Picture Size (Diagonal) | mm
16.5 inches |
| Effective Picture Size (H x V) | 365.8 x 205.7 mm
14 1/2 x 8 1/8 inches |
| Resolution (H x V) | 1920 x 1080 pixels (Full HD) |
| Aspect | 16:9 |
| Pixel Efficiency | 99.99% |
| Colors | Approx. 1,073 million colours |
| Viewing Angle (Panel Specification) | 89°/89°/89°/89° (typical) (up/down/left/right contrast > 10:1) |
| Normal Scan | 0% scan |
Input:
| Composite Input | BNC (x1), 1 Vp-p ±3dB, sync negative |
| SDI Input | BNC (x2) |
| HDMI Input | HDMI (x1) (HDCP correspondence) |
| Audio Input | Stereo mini jack (x1), -5 dBu 47 kΩ or higher |
| Parallel Remote | RJ-45 Modular connector 8-pin (x1)
(Pin-assignable) |
| Serial Remote (LAN) | RJ-45 (x1) (Ethernet, 10BASE-T/100BASE-TX) |
| DC Input | XLR-type 4-pin (male) (x1), DC 12 V to 17 V (output impedance 0.05 Ω or less) |
Output:
| Composite Output | BNC (x1), Loop-through, with 75 Ω automatic terminal function |
| SDI Output | BNC (x2), output signal amplitude: 800 mVp-p ±10%, output impedance: 75 Ω unbalanced |
| Audio Monitor Output | Stereo mini jack (x1) |
| Speaker (Built-in) Output | 1.0 W (Monaural) |
| Headphone Output | Stereo mini jack (x1) |
General:
| Power Requirements | 100 V to 240 V AC, 0.5 A to 0.2 A, 50/60 Hz
DC 12 V to 17 V, 3.6 A to 2.5 A |
| Power Consumption | Approx. 49 W (max.)
Approx. 42 W (average power consumption in the default sattus) |
| Inrush Current | (1) Maximum possible inrush current at initial switch-on (Voltage changes caused by manual switching): 60 A peak, 0.3 A r.m.s. (240V AC)
(2) Inrush current after a mains interruption of five seconds (Voltage changes caused at zero-crossing): 48 A peak, 0.2 A r.m.s. (240V AC) |
| Operating Temperature | 0°C to 35°C (Recommended: 20°C to 30°C)
32°F to 95°F (Recommended: 68°F to 86°F) |
| Operating Humidity | 30% to 85% (no condensation) |
| Storage/Transport Temperature | -20°C to +60°C
-4°F to +140°F |
| Storage/Transport Humidity | 0% to 90% |
| Operating/Storage/Transport Pressure | 700 hPa to 1060 hPa |
| Dimensions (W x H x D) *1 | 420.2 x 288.8 x 70.0 mm (without monitor feet)
420.2 x 311.3 x 165.0 (with monitor feet)
16 5/8 x 11 3/8 x 2 7/8 inches (without monitor feet)
16 5/8 x 12 3/8 x 6 1/2 inches (with monitor feet) |
| Mass | Approx. 4.9 kg (with monitor feet)
Approx. 10 lb 13 oz (with monitor feet)
Approx. kg (without monitor feet)
Approx. lb oz (without monitor feet) |
| Supplied Accessories | AC power cord (1)
AC plug holder (1)
Handle (1) (including 4 screws)
Before Using This Unit (1)
CD-ROM (1) |
| Optional Accessories | SU-561 Monitor Stand
SU-562 Monitor Stand
BKM-PL17
MB-L17
|
Notes:
| Note | *1 The values for dimensions are approximate. |
Sony BKM-PL17 műszaki adatok:
AR-coated protection panel for LMD-A170 17-inch high grade LCD monitorThis accessory provides an (anti-reflective) AR-coated polycarbonate protection panel for the portable 17-inch monitor, along with corner bumpers to safeguard the monitor from scratches and impact. The benefit of this is significant when renting out these monitors – for example, panel damage is reduced and there is a far lower incidence of panel replacement and downtime during rental cycles.
Safeguard from scratches and impactAR-coated tough polycarbonate protection panel and corner bumpers.
Easy clean surfaceFor cleaning the protection panel, wipe it gently with the supplied cleaning cloth.
High transparency, low reflection surfaceThe lightweight panel allows you to see the monitor images clearly.
Simple attachment/detachment mechanismCorner bumpers have finger/coin-tighten screws and drop prevention washers. Easily, quickly attachable and detachable on-site.
Features:AR-coated protection panelThe (anti-reflective) AR-coated protection panel is designed to fit precisely on the LMD-A170 monitor front surface.
Corner bumpers with simple attachment/detachment mechanismCorner bumpers hold the front panel in place and protect the monitor from accidental damage in the field. The corner bumpers have finger/coin-tighten screws and drop prevention washers. They are easily, quickly attachable and detachable on-site.
Magunkról
Szállítás
Kapcsolat
